|
kindasleepy
Sep 11, 2011, 11:33 PM
Post #1 of 15
(9209 views)
Shortcut
Registered: Nov 19, 2003
Posts: 51
|
I am wondering what other developers are using for top anchors on routes they put up. I typically use Fixe Ring Rappel Anchors in pairs. I have started developing a steep face which would very nice to have fixed chain draws on. They are kinda pricey from Fixe. Living in Canada, I have to pay about 35% more just for the shipping and then the duty at the border. I am looking at about 30-40$ per draw. They are basically SS quick link, 3 links of chain and then a steel biner. I have been looking in Marine Stores but no one can give me load strengths or quality assurance. Is everybody sucking up the cost of these draws or are they using something else. I have seen them used in Rumney and I know they are used in many area's. Note: I am an experienced developer with over 10 years climbing, 5 years developing and at least 30 routes bolted but I have lost count.
|
|
|
|
|
rocknice2
Sep 11, 2011, 11:56 PM
Post #2 of 15
(9198 views)
Shortcut
Registered: Jul 13, 2006
Posts: 1221
|
I use these as a pair = cheapest $$ anchor I know Order them from MEC. No duties http://www.mec.ca/...38-rappel-hanger.jsp No chain at all. I place them staggered Place 1 above the other but just slightly to the side, so when the upper ring is on say the left side of the hanger and the bottom is on the right side. The rings line up. The reason for this is that I find when they are placed horizontally, they twist the rope as it's being pull through. Some argue that it doesn't divide the load between the 2 hangers. This is very true. I say, 1 is plenty strong enough to rap off of and you have a 2nd for backup. As we all know shock load is a myth. Added bonus is as the ring wears you only need to replace 1 not both. Try it out on one of your routes I'm sure you'll get to like this setup.
(This post was edited by rocknice2 on Sep 11, 2011, 11:59 PM)
|
|
|
|
|
rockforlife
Sep 12, 2011, 4:39 AM
Post #3 of 15
(9135 views)
Shortcut
Registered: May 14, 2002
Posts: 563
|
rocknice2 wrote: I use these as a pair = cheapest $$ anchor I know Order them from MEC. No duties http://www.mec.ca/...38-rappel-hanger.jsp No chain at all. I place them staggered Place 1 above the other but just slightly to the side, so when the upper ring is on say the left side of the hanger and the bottom is on the right side. The rings line up. The reason for this is that I find when they are placed horizontally, they twist the rope as it's being pull through. Some argue that it doesn't divide the load between the 2 hangers. This is very true. I say, 1 is plenty strong enough to rap off of and you have a 2nd for backup. As we all know shock load is a myth. Added bonus is as the ring wears you only need to replace 1 not both. Try it out on one of your routes I'm sure you'll get to like this setup. hmmm....Really...
|
|
|
|
|
|
|
|
JimTitt
Sep 12, 2011, 6:27 AM
Post #5 of 15
(9115 views)
Shortcut
Registered: Aug 7, 2008
Posts: 1002
|
By definition if the top anchor failed the impact force on the lower anchor wil be extremely low since the fall is a matter of inches and the rope out is as a minimum the full height of the climb. Thus the fall factor is minimal. The way described is the prefered method and the one we recommend to our customers. Jim
|
|
|
|
|
tolman_paul
Sep 12, 2011, 9:22 PM
Post #6 of 15
(9016 views)
Shortcut
Registered: Apr 22, 2005
Posts: 385
|
If you're going to be installing many rap stations and want to keep your costs down, go to a hardware store and cut 3/8" chain to 1' lengths with an even number of links. Set a 1/2" X 5 1/2" wedge anchor with double washers and tighen the bolt directly to the chain. Beefy, reasonably inexpensive if you get your bolts in bulk, and the chain is easily replaced when it gets worn.
|
|
|
|
|
jakedatc
Sep 12, 2011, 9:54 PM
Post #7 of 15
(8999 views)
Shortcut
Registered: Mar 12, 2003
Posts: 11054
|
tolman_paul wrote: If you're going to be installing many rap stations and want to keep your costs down, go to a hardware store and cut 3/8" chain to 1' lengths with an even number of links. Set a 1/2" X 5 1/2" wedge anchor with double washers and tighen the bolt directly to the chain. Beefy, reasonably inexpensive if you get your bolts in bulk, and the chain is easily replaced when it gets worn. small link chain is such a pain in the ass. And not using real bolts is a disservice to anyone down the line who then has to replace the whole thing instead of just the links. threading 3/8ths is a pain and can twist the rope if you don't line it up right. Normal bolts + hangers (or glue ins) 2 beefy 1/2" links and you're good to go. easy to clean, straight rope line, really hard to wear out, can get links in bulk pretty cheap.
|
|
|
|
|
granite_grrl
Sep 12, 2011, 10:29 PM
Post #8 of 15
(8984 views)
Shortcut
Registered: Oct 25, 2002
Posts: 15084
|
That's one expensive mussy hook! To the OP, we normally use Fixe rap rings from MEC like the ones posted earlier in this thread. Mussy hooks are super nice to have on popular routes, but I don't know a good source for them in Canada.
|
|
|
|
|
6pacfershur
Sep 13, 2011, 12:27 AM
Post #9 of 15
(8956 views)
Shortcut
Registered: Jun 23, 2010
Posts: 254
|
rocknice2 wrote: I use these as a pair = cheapest $$ anchor I know Order them from MEC. No duties http://www.mec.ca/...38-rappel-hanger.jsp In reply to: everyone please note; they are called "rappel hangers", not "lowering hangers" : thanx for the link R&I
|
|
|
|
|
jakedatc
Sep 13, 2011, 12:40 AM
Post #10 of 15
(8948 views)
Shortcut
Registered: Mar 12, 2003
Posts: 11054
|
6pacfershur wrote: everyone please note; they are called "rappel hangers", not "lowering hangers" : thanx for the link R&I Please note, It's the Sport Forum. cheezetitting gumbie
(This post was edited by jakedatc on Sep 13, 2011, 12:42 AM)
|
|
|
|
|
jt512
Sep 13, 2011, 3:46 AM
Post #11 of 15
(8885 views)
Shortcut
Registered: Apr 12, 2001
Posts: 21904
|
jakedatc wrote: 6pacfershur wrote: everyone please note; they are called "rappel hangers", not "lowering hangers" : thanx for the link R&I Please note, It's the Sport Forum. cheezetitting gumbie Five stars for the phrase "cheezetitting gumbie."
|
|
|
|
|
acorneau
Sep 13, 2011, 1:00 PM
Post #12 of 15
(8836 views)
Shortcut
Registered: Feb 6, 2008
Posts: 2889
|
I still have 12 SS Maillon Rapide 9mm delta quicklinks that I need to get rid of. All you would need to add is the hangers and bolts. Deltas are the same as the ones on the top row. They're nice because the delta is large enough to have a couple of biners on there and still have plenty of room to stuff a bight of rope through. If/when they get worn out you can swap them out as needed. Let me know via PM if you're interested.
|
|
|
|
|
kindasleepy
Sep 14, 2011, 7:20 PM
Post #13 of 15
(8767 views)
Shortcut
Registered: Nov 19, 2003
Posts: 51
|
Thanks for all the feedback. I currently use Fixe Rap Anchors in pairs at the top of my routes. I expect heavy travel and want fixed biners at the top so people could just lower off. I am not interested in various ways of placing rap achors. What do you use for fixed binerss?
|
Attachments:
|
P4050123.jpg
(129 KB)
|
|
|
|
|
jakedatc
Sep 14, 2011, 8:27 PM
Post #14 of 15
(8733 views)
Shortcut
Registered: Mar 12, 2003
Posts: 11054
|
kindasleepy wrote: Thanks for all the feedback. I currently use Fixe Rap Anchors in pairs at the top of my routes. I expect heavy travel and want fixed biners at the top so people could just lower off. I am not interested in various ways of placing rap achors. What do you use for fixed binerss? If you have ring anchors then why not just leave them like that. Threading takes like 1min max and will prevent people from TRing on your stuff.(usually)
|
|
|
|
|
rocknice2
Sep 14, 2011, 11:18 PM
Post #15 of 15
(8685 views)
Shortcut
Registered: Jul 13, 2006
Posts: 1221
|
I have used the Fixe SS biners but this gets $$ fast. I tried on sale alum. biners first. I wired them to the chain so it doesnt get stolen too easily but these were more expensive than steel or ss biners.
|
|
|
|
|
|