Forums: Climbing Information: Gear Heads:
What determines the rate at which a cam will rip out?
RSS FeedRSS Feeds for Gear Heads

Premier Sponsor:

 
First page Previous page 1 2 Next page Last page  View All


Onlyoriginal


Sep 26, 2012, 2:19 AM
Post #1 of 30 (5366 views)
Shortcut

Registered: Mar 31, 2012
Posts: 26

What determines the rate at which a cam will rip out?
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

Is there anything when buying a piece of protection, that shows when it will rip out of the wall?
Like how much force is needed to pull it outa the wall?

Does the strength of the protection have anything to do with this?


jowybyo


Sep 26, 2012, 5:15 AM
Post #2 of 30 (5338 views)
Shortcut

Registered: Aug 6, 2012
Posts: 20

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

No....the force required to fail a placement is based on the strength of the rock, the friction between the rock and the gear, and the overall quality of the placement itself.

Protection does come with a rating for it's ultimate strength, but this is the force required to break the gear not rip it from rock.

-Joe B.


andrewluke


Sep 26, 2012, 5:15 AM
Post #3 of 30 (5338 views)
Shortcut

Registered: Dec 8, 2011
Posts: 14

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

It all depends on the rock.


patto


Sep 26, 2012, 6:14 AM
Post #4 of 30 (5317 views)
Shortcut

Registered: Nov 14, 2005
Posts: 1446

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (2 ratings)  
Can't Post

In theory and in most of the time in practice a cam will either pull at very light loads ie a tug with your hand. Or hold until the rock or cam breaks.

The exception is when the cam is close to the threshold of slipping but not at it. In this case a cam may slip at lower loads due to flex and compression of the cam lobes.


Of course if the cam is not aligned with the direction of the fall and moves when loaded then that can significantly affect outcomes.


acorneau


Sep 26, 2012, 6:24 AM
Post #5 of 30 (5314 views)
Shortcut

Registered: Feb 6, 2008
Posts: 2889

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

One should also mention that it has been shown that even for the most bomber of placements most will only hold ~10kN before ripping out.


USnavy


Sep 26, 2012, 9:38 AM
Post #6 of 30 (5277 views)
Shortcut

Registered: Nov 5, 2007
Posts: 2650

Re: [patto] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (3 ratings)  
Can't Post

patto wrote:
In theory and in most of the time in practice a cam will either pull at very light loads ie a tug with your hand. Or hold until the rock or cam breaks.
I dont know what theory you are studying. Every cam I have ever pulled on a bounce test while climbing aid held static bodyweight. It was not until I started bounce testing the piece that it pulled. Also, most of the cams I have ripped on a fall would have likely held bodyweight as in most cases I could feel the piece tug on the rope before ripping. But, many of those cases involved the rock breaking right under the lobes, so I guess that would fall into your exception clause. Anyway, just because a piece will withstand a tug from your hand does not mean it will arrest a lead fall.


(This post was edited by USnavy on Sep 26, 2012, 9:41 AM)


Partner cracklover


Sep 26, 2012, 9:58 AM
Post #7 of 30 (5263 views)
Shortcut

Registered: Nov 14, 2002
Posts: 9935

Re: [patto] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

patto wrote:
In theory and in most of the time in practice a cam will either pull at very light loads ie a tug with your hand.

In theory, perhaps, but in practice, this couldn't be more wrong. Tons of placements look anywhere from bomber to scary-as-fuck, and will hold more than a hard tug, but less than full strength.

GO


petsfed


Sep 26, 2012, 10:12 AM
Post #8 of 30 (5255 views)
Shortcut

Registered: Sep 24, 2002
Posts: 8585

Re: [cracklover] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

cracklover wrote:
patto wrote:
In theory and in most of the time in practice a cam will either pull at very light loads ie a tug with your hand.

In theory, perhaps, but in practice, this couldn't be more wrong. Tons of placements look anywhere from bomber to scary-as-fuck, and will hold more than a hard tug, but less than full strength.

GO

And this is due almost entirely to the coefficient of friction changing following the destruction of the rock's surface when the cam is loaded.

Patto is not wrong, its just that confirmation bias and a complex reality tend to obscure the theory he's pointing out. The point was that if you look only at the tangent angle and how close the crack is to parallel, but ignore the rock quality of the placement, you'll get a bimodal failure distribution, with peaks at fall-strength and light-tug-with-your-hand. That doesn't mean there isn't a gray area, just that what puts a placement into that gray area has a lot to do with the rock quality. That is, a placement that might fail well above a body-weight load in good, high friction rock might fail at well below body-weight in slick or crumbly rock. If you only compare similarly hard rock, then cams placed in the rock with the higher coefficient of friction will fail less than those in slicker rock in otherwise identical placements.


Partner cracklover


Sep 26, 2012, 11:07 AM
Post #9 of 30 (5235 views)
Shortcut

Registered: Nov 14, 2002
Posts: 9935

Re: [petsfed] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

petsfed wrote:
cracklover wrote:
patto wrote:
In theory and in most of the time in practice a cam will either pull at very light loads ie a tug with your hand.

In theory, perhaps, but in practice, this couldn't be more wrong. Tons of placements look anywhere from bomber to scary-as-fuck, and will hold more than a hard tug, but less than full strength.

GO

And this is due almost entirely to the coefficient of friction changing following the destruction of the rock's surface when the cam is loaded.

Patto is not wrong, its just that confirmation bias and a complex reality tend to obscure the theory he's pointing out. The point was that if you look only at the tangent angle and how close the crack is to parallel, but ignore the rock quality of the placement, you'll get a bimodal failure distribution, with peaks at fall-strength and light-tug-with-your-hand. That doesn't mean there isn't a gray area, just that what puts a placement into that gray area has a lot to do with the rock quality. That is, a placement that might fail well above a body-weight load in good, high friction rock might fail at well below body-weight in slick or crumbly rock. If you only compare similarly hard rock, then cams placed in the rock with the higher coefficient of friction will fail less than those in slicker rock in otherwise identical placements.

No, it's just plain silly. You're calling an "exception" nearly every single fall that happens in the real world. I doubt there are many real falls (not counting just slumping onto the piece) that do not cause the cam to either move somewhat, or crack, crush, or dislocate some crystals.

I suspect that the true failure load of cams in the field would be not so much your "bimodal distribution" (with peaks at light tug with your hand and the strength stamped on the cam) but more like a high peak around the rated failure, and then a gradual slope from the strength stamped on the cam down.

There are so many factors that impact the failure strength of the cam, and so many imperfect placements that work "well enough".

GO


(This post was edited by cracklover on Sep 26, 2012, 11:10 AM)


petsfed


Sep 26, 2012, 12:08 PM
Post #10 of 30 (5197 views)
Shortcut

Registered: Sep 24, 2002
Posts: 8585

Re: [cracklover] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

I think anybody experienced in placing gear would agree that simply looking at the geometry of the placement, and not the rock its placed in, would consistently result in bad placements. Patto's statement only refers to the geometry of the placement. So does mine.

The gray area comes from the fact that we're not simply looking for parallel placements when placing cams, but also situations that prevent walking, that have good rock, that don't result in a junk placement if they walk, etc.


Partner cracklover


Sep 26, 2012, 2:06 PM
Post #11 of 30 (5162 views)
Shortcut

Registered: Nov 14, 2002
Posts: 9935

Re: [petsfed] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

petsfed wrote:
I think anybody experienced in placing gear would agree that simply looking at the geometry of the placement, and not the rock its placed in, would consistently result in bad placements. Patto's statement only refers to the geometry of the placement. So does mine.

The gray area comes from the fact that we're not simply looking for parallel placements when placing cams, but also situations that prevent walking, that have good rock, that don't result in a junk placement if they walk, etc.

The point I'm trying to make is that all my experience leads me to suspect that many placements (at least for cams roughly an inch and a half or smaller), placements you and I use every day and call good enough, are squarely in that "gray area".

These placements would, if subjected to a serious fall, fail at significantly below the rated strength of the cam. The reasons are myriad, and not worth going into here. The point is that the notion that a cam is either "good" or "bad" in the real world is simply silly and misleading.

Sure, I could find you placements where I'd bet good money that the cam would fail at it's rated strength, but in the real world, such placements are often nothing more than a pipe dream, and we go with what's "good enough".

The only scary thing, to me, is that I bet that most people wouldn't know the difference between a "good enough" placement and a truly bomber one. Fortunately, it rarely matters, since most of us don't go around taking big whippers most of the time.

GO


sween345


Sep 26, 2012, 2:26 PM
Post #12 of 30 (5153 views)
Shortcut

Registered: May 13, 2006
Posts: 249

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

 Only,

This will explain it....http://www.bigwalls.net/climb/camf/index.html


patto


Sep 26, 2012, 3:45 PM
Post #13 of 30 (5122 views)
Shortcut

Registered: Nov 14, 2005
Posts: 1446

Re: [cracklover] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

cracklover wrote:
No, it's just plain silly. You're calling an "exception" nearly every single fall that happens in the real world. I doubt there are many real falls (not counting just slumping onto the piece) that do not cause the cam to either move somewhat, or crack, crush, or dislocate some crystals.

It all depends on the situations and the rock you climb. The rock I climb on doesn't have "crystals".

The majority of my trad climbing is done on strong, fine grained homogeneous rock. This minor means that rock failure pretty much wont occur so that rules out one failure mode. Movement isn't a big deal if the crack is fairly regular and the cam is placed very close to the line of fall. This leads smooth slippery cracks as the main failure mode (low coefficient of friction). In practice at this crag most cam failures are of this type.

Contrast this with say course rock climbing. Coefficient of friction here is normally significantly higher so straight forward slipping is rare. Breaking of crystals and ripping out pulling rock with it is the common failure mode.


curt


Sep 26, 2012, 3:54 PM
Post #14 of 30 (5115 views)
Shortcut

Registered: Aug 26, 2002
Posts: 18226

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

Onlyoriginal wrote:
Is there anything when buying a piece of protection, that shows when it will rip out of the wall?
Like how much force is needed to pull it outa the wall?

No.

Onlyoriginal wrote:
Does the strength of the protection have anything to do with this?

No.

Curt


patto


Sep 26, 2012, 4:01 PM
Post #15 of 30 (5112 views)
Shortcut

Registered: Nov 14, 2005
Posts: 1446

Re: [cracklover] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

cracklover wrote:
The point I'm trying to make is that all my experience leads me to suspect that many placements (at least for cams roughly an inch and a half or smaller), placements you and I use every day and call good enough, are squarely in that "gray area".

These placements would, if subjected to a serious fall, fail at significantly below the rated strength of the cam. The reasons are myriad, and not worth going into here. The point is that the notion that a cam is either "good" or "bad" in the real world is simply silly and misleading.

Sure, I could find you placements where I'd bet good money that the cam would fail at it's rated strength, but in the real world, such placements are often nothing more than a pipe dream, and we go with what's "good enough".

The only scary thing, to me, is that I bet that most people wouldn't know the difference between a "good enough" placement and a truly bomber one. Fortunately, it rarely matters, since most of us don't go around taking big whippers most of the time.

GO

Comments like these make me think you climb on really shit rock. I place cams all the way down to the Green ZERO, which is 1/3 of an inch. (Though I haven't falled on greeny.)

Here are some real world tests of trad gear. The sandstone where this gear was placed is renowned for its poor quality for trad gear. (though it isn't as bad as really shitty sandstone.)
http://www.sanguma.org/...ructo/placements.php

Your comments that decent most cams can hole light falls but not big whippers are simply not true for decent cams good rock.


petsfed


Sep 26, 2012, 5:16 PM
Post #16 of 30 (5089 views)
Shortcut

Registered: Sep 24, 2002
Posts: 8585

Re: [patto] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

I can't speak for cracklover, but if you actually believe that all the things you don't have to consider aren't a MAJOR factor in piece quality, then you really need to travel more, or you misunderstood my defense of your statements.


patto


Sep 26, 2012, 5:39 PM
Post #17 of 30 (5076 views)
Shortcut

Registered: Nov 14, 2005
Posts: 1446

Re: [petsfed] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

petsfed wrote:
I can't speak for cracklover, but if you actually believe that all the things you don't have to consider aren't a MAJOR factor in piece quality, then you really need to travel more, or you misunderstood my defense of your statements.

I'm not sure what you mean here... Maybe I wasn't clear in my above statements.

I have travelled a fair bit and climbed in different locations, different countries and on different rock. I've never had gear pull on me when resting on it or falling. I try not to fall too regularly, I took a couple of whippers on cams last time I was in Yosemite.


bearbreeder


Sep 26, 2012, 6:16 PM
Post #18 of 30 (5059 views)
Shortcut

Registered: Feb 1, 2009
Posts: 1960

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

Onlyoriginal wrote:
Is there anything when buying a piece of protection, that shows when it will rip out of the wall?
Like how much force is needed to pull it outa the wall?

Does the strength of the protection have anything to do with this?

as pointed out the answer is no ...


Partner cracklover


Sep 27, 2012, 8:22 AM
Post #19 of 30 (4963 views)
Shortcut

Registered: Nov 14, 2002
Posts: 9935

Re: [patto] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

patto wrote:
cracklover wrote:
The point I'm trying to make is that all my experience leads me to suspect that many placements (at least for cams roughly an inch and a half or smaller), placements you and I use every day and call good enough, are squarely in that "gray area".

These placements would, if subjected to a serious fall, fail at significantly below the rated strength of the cam. The reasons are myriad, and not worth going into here. The point is that the notion that a cam is either "good" or "bad" in the real world is simply silly and misleading.

Sure, I could find you placements where I'd bet good money that the cam would fail at it's rated strength, but in the real world, such placements are often nothing more than a pipe dream, and we go with what's "good enough".

The only scary thing, to me, is that I bet that most people wouldn't know the difference between a "good enough" placement and a truly bomber one. Fortunately, it rarely matters, since most of us don't go around taking big whippers most of the time.

GO

Comments like these make me think you climb on really shit rock. I place cams all the way down to the Green ZERO, which is 1/3 of an inch. (Though I haven't falled on greeny.)

Here are some real world tests of trad gear. The sandstone where this gear was placed is renowned for its poor quality for trad gear. (though it isn't as bad as really shitty sandstone.)
http://www.sanguma.org/...ructo/placements.php

Your comments that decent most cams can hole light falls but not big whippers are simply not true for decent cams good rock.

I climb on a variety of rock, and make a variety of placements in that rock. I'll just give a few examples:

In even the hardest and most parallel of desert sandstone, I'm absolutely sure that a hard fall on a small cam will cause it to track at least a little. Depending on how deep the cam is (some placements are simply shallow, there's nothing to be done about it) that could mean a ripped placement from a hard fall.

In even the hardest granite, you sometimes must make do with a shallow cam in a pin scar. Expecting these to hold a hard fall is wishful thinking. A buddy of mine recently fell and ripped four such cams from their placements - all of which he thought were truck.

Those are just a couple examples of gear that looks - not perfect, but good enough. And these pieces will certainly hold, but will pull out before they break.

BTW, your link does little to bolster your point. There were only two cams tested, and in both cases, they tracked out, undamaged. In one case, it tracked out even though it was behind a bottleneck, which is the one case where a cam should be absolutely solid. So much for your theory that it either comes out with a tug or hold until it breaks or the rock crumbles.

GO


(This post was edited by cracklover on Sep 27, 2012, 8:24 AM)


patto


Sep 27, 2012, 3:53 PM
Post #20 of 30 (4871 views)
Shortcut

Registered: Nov 14, 2005
Posts: 1446

Re: [cracklover] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

cracklover wrote:
In even the hardest and most parallel of desert sandstone, I'm absolutely sure that a hard fall on a small cam will cause it to track at least a little.
Then the rock isn't hard or it is glassy smooth.

If a small cam (and by small I mean Metolius 0 or below) start tracking then its pretty much all over. If its "tracking" then you are going to have lubricating rock dust. If it is slipping or sliding then the lower kinetic friction will likely mean it will continue.

If you are suggesting that a cam moving out and then stopping is common in cam behaviour then you clearly don't understand the mechanics here. Once a cam moves in the direction of fall then in all likelyhood its not going to stop. (Unless you are talking slight compression movement that is visible on all big cams on even a hand tug.)


cracklover wrote:
In even the hardest granite, you sometimes must make do with a shallow cam in a pin scar. Expecting these to hold a hard fall is wishful thinking. A buddy of mine recently fell and ripped four such cams from their placements - all of which he thought were truck.
Your buddy needs to assess his gear placements better.

cracklover wrote:
Those are just a couple examples of gear that looks - not perfect, but good enough. And these pieces will certainly hold, but will pull out before they break.
No they are not.

cracklover wrote:
BTW, your link does little to bolster your point. There were only two cams tested, and in both cases, they tracked out, undamaged. In one case, it tracked out even though it was behind a bottleneck, which is the one case where a cam should be absolutely solid. So much for your theory that it either comes out with a tug or hold until it breaks or the rock crumbles
One cam tracked out leaving scores in the rock. Ie the rock sheared and failed as mentioned in the comments. The other had a wedged block move and it released the cam.

Onlyoriginal asked a question and I answered by mentioning behaviour in strong cohesive rock. Sure if the rock is really shit failure can occur at lower loads that is long been recognised. But whats your point again?


(This post was edited by patto on Sep 27, 2012, 4:04 PM)


Partner robdotcalm


Sep 27, 2012, 5:17 PM
Post #21 of 30 (4850 views)
Shortcut

Registered: Oct 31, 2002
Posts: 1023

Re: [patto] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

patto wrote:
In theory and in most of the time in practice a cam will either pull at very light loads ie a tug with your hand. Or hold until the rock or cam breaks.
.

Earlier testing by Ocean Pacific after the failure of a link cam indicated that tugging on a cam after placement enhanced the holding power of the cam even for poor quality placements. Perhaps this is what's being referred to.

"One interesting thing we noted was how important "setting" the piece was. A simple tug on the gear before it's loaded made a difference in whether the gear held or popped. Even some compromised placements that were spit out when we didn't "set" the piece held fast when the gear was "set" prior to the load”

http://www.rockclimbing.com/..._reply;so=ASC;mh=25;

rob.calm


petsfed


Sep 27, 2012, 6:36 PM
Post #22 of 30 (4833 views)
Shortcut

Registered: Sep 24, 2002
Posts: 8585

Re: [patto] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

Ok, now you're waaay off.

In reply to:
If you are suggesting that a cam moving out and then stopping is common in cam behaviour then you clearly don't understand the mechanics here. Once a cam moves in the direction of fall then in all likelyhood its not going to stop. (Unless you are talking slight compression movement that is visible on all big cams on even a hand tug.)

This is a direct result of inhomogeneity of the rock. That is, the rock is not going to have the same coefficient of friction everywhere, and can be affected by a lot of different things. Also, if the rock is not perfectly parallel, then what is insufficient friction for one contact angle may be sufficient friction for another contact angle. It could also be the case that what's causing these short tracking events is that deep in the crack, there's much more lubricating grit, and further out, much less. If you actually believe that the rock will exhibit as much consistency as you claim it does, I've got a bridge I think you might be interested in buying. By and large, cams placed in parallel cracks don't fail, and tracking leads directly to failure. But flaring, shallow, and uneven cracks are where it gets hard and scary, and then all bets are off.

There are climbs in the Moab area of Utah where you can see distinctive tank-tread like marks in the cracks from the shear volume of people whipping on cams in soft rock, and I'd wager a few of those placements failed, but what caused the track marks is the pulverization of the surface, and the movement of the cam to a stronger position.


hugepedro


Sep 27, 2012, 10:45 PM
Post #23 of 30 (4802 views)
Shortcut

Registered: May 28, 2002
Posts: 2875

Re: [Onlyoriginal] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

O M G

Let's simplify this.

When you were young, did you play with:

1. Legos, Erector Set, and Lincoln Logs (or something similar, I am old, so these specific toys may not be relevant).

or did you play with:

Play Doh, G.I. Joe, and Care Bears

If it was the former, you're probaly ok. If it was the latter, you probably shouldn't be trad climbing.


petsfed


Sep 28, 2012, 12:18 AM
Post #24 of 30 (4794 views)
Shortcut

Registered: Sep 24, 2002
Posts: 8585

Re: [hugepedro] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

I played with both.

Strength or weakness?


hugepedro


Sep 28, 2012, 12:28 AM
Post #25 of 30 (4791 views)
Shortcut

Registered: May 28, 2002
Posts: 2875

Re: [petsfed] What determines the rate at which a cam will rip out? [In reply to]
Report this Post
Average: avg_1 avg_2 avg_3 avg_4 avg_5 (0 ratings)  
Can't Post

petsfed wrote:
I played with both.

Strength or weakness?

You played with Care Bears? That's fabulous.

First page Previous page 1 2 Next page Last page  View All

Forums : Climbing Information : Gear Heads

 


Search for (options)

Log In:

Username:
Password: Remember me:

Go Register
Go Lost Password?



Follow us on Twiter Become a Fan on Facebook