|
corno32
Oct 12, 2012, 4:53 AM
Post #1 of 19
(14348 views)
Shortcut
Registered: May 7, 2012
Posts: 17
|
hi I use a wiregate carabiner with the usual keylock configuration at the moment to rack my BD and dmm nuts. It's annoying to have the nut wire catch the notch sometimes as I go to use them, I'd like to try a carabiner that's smooth without the keylock notch. Anyone have a favorite carabiner that isn't a keylock that works well for racking these? thx
|
|
|
|
|
petsfed
Oct 12, 2012, 8:00 AM
Post #2 of 19
(14319 views)
Shortcut
Registered: Sep 25, 2002
Posts: 8599
|
corno32 wrote: hi I use a wiregate carabiner with the usual keylock configuration at the moment to rack my BD and dmm nuts. It's annoying to have the nut wire catch the notch sometimes as I go to use them, I'd like to try a carabiner that's smooth without the keylock notch. Anyone have a favorite carabiner that isn't a keylock that works well for racking these? thx You're confusing two terms: A traditional hooked carabiner has a hook that hooks a pin in the gate, or the wire on a wiregate. A keylock carabiner (the term is trademarked by petzl) does not have such a hook. I like the positrons. Others like the spirits. Personally, I prefer an oval for my nuts, because they don't bunch together as much. To be honest, I actually prefer a traditional hooked carabiner because the nuts are less likely to spill off unexpectedly if the crab comes open accidentally.
|
|
|
|
|
rocknice2
Oct 12, 2012, 11:01 AM
Post #3 of 19
(14297 views)
Shortcut
Registered: Jul 13, 2006
Posts: 1221
|
I hate notched biners. The whole rack is notchless, with the exception of the 2 stopper racking biners. That little notch comes in handy for capturing runaway nuts.
|
|
|
|
|
wonderwoman
Oct 12, 2012, 1:30 PM
Post #5 of 19
(14256 views)
Shortcut
Registered: Dec 14, 2002
Posts: 4275
|
Moved from general to gear heads by ww. I prefer notchless, too. However, my good biners are for my gear. My nuts are on bail biners that we have come across. One is an notched oval with a nice little rope groove in it from being bailed on so many times, I suppose. The wires sit nicely in the groove. And I get what you say about the wires getting stuck in the notch, but it hasn't been that big of an issue for me.
|
|
|
|
|
bearbreeder
Oct 12, 2012, 1:55 PM
Post #6 of 19
(14249 views)
Shortcut
Registered: Feb 2, 2009
Posts: 1960
|
patto wrote: If you are getting run away nuts then you are doing it wrong! ( IMO) At no stage should the biner be open except when the desired nut is placed and all the nuts are in the bottom basket. When this occurs the gate can be opened and the emplaced nut slipped off aided by no notch. No possibility of runaway nuts. I carry 30 nuts while climbing racked across 3 oval notchless biners. same here ... the trick is to place the nut, set it, rotate the biner and then let the nuts bunch at the bottom before taking away the biner .... for nuts i personally like - notchless biners ... last thing i want is the notch catching when im placing a nut when hanging from a fingerlock ... those placements when you have to place right after the crux or where the entire climb is one big crux - for "hard" (for me 11+/12-) trad climbs i place no more than 5-6 nuts per biner ... the last thing you want is to try to mess around with 10+ nuts per biner in said pumpy placement ... also the fewer nuts on a biner the less chance i find of dropping them when placing - solid gate biners ... i find that for hard fast placements i can hold the biner easier and set em fast .... also should the need arise, ill have enough solid gates for a biner brake but then each to his/her own ... unless yr climbing at yr very limit, anything will work ... and even then you just need to get stronger, well i certainly do, if something as minor as notches are preventing you from climbing hard
|
|
|
|
|
corno32
Oct 12, 2012, 2:43 PM
Post #7 of 19
(14208 views)
Shortcut
Registered: May 7, 2012
Posts: 17
|
petsfed wrote: corno32 wrote: hi I use a wiregate carabiner with the usual keylock configuration at the moment to rack my BD and dmm nuts. It's annoying to have the nut wire catch the notch sometimes as I go to use them, I'd like to try a carabiner that's smooth without the keylock notch. Anyone have a favorite carabiner that isn't a keylock that works well for racking these? thx You're confusing two terms: A traditional hooked carabiner has a hook that hooks a pin in the gate, or the wire on a wiregate. A keylock carabiner (the term is trademarked by petzl) does not have such a hook. I like the positrons. Others like the spirits. Personally, I prefer an oval for my nuts, because they don't bunch together as much. To be honest, I actually prefer a traditional hooked carabiner because the nuts are less likely to spill off unexpectedly if the crab comes open accidentally. Doh okay got it on the terminology thanks. I like the oval idea, interesting on using a positron or spirit thanks
|
|
|
|
|
corno32
Oct 12, 2012, 2:47 PM
Post #8 of 19
(14202 views)
Shortcut
Registered: May 7, 2012
Posts: 17
|
patto wrote: No possibility of runaway nuts. I carry 30 nuts while climbing racked across 3 oval notchless biners. Most of the rest of my rack are notched biners of phantoms and neutrinos. I'd slightly prefer light notchless but heliums are not cheap! notchless ovals sound very nice, are you talking about something like the aluminum smc ? I can't find any other notchless ovals thanks
|
|
|
|
|
rocknice2
Oct 12, 2012, 2:48 PM
Post #9 of 19
(14201 views)
Shortcut
Registered: Jul 13, 2006
Posts: 1221
|
patto wrote: rocknice2 wrote: I hate notched biners. The whole rack is notchless, with the exception of the 2 stopper racking biners. That little notch comes in handy for capturing runaway nuts. If you are getting run away nuts then you are doing it wrong! ( IMO) At no stage should the biner be open except when the desired nut is placed and all the nuts are in the bottom basket. Your acting like accidents never happen. Should is the key word in your statement. That notch can hinder or help. It can bugger you if you don't remove the biner from the placed nut properly. It can save a nut if you don't have all your non-placed nuts at the bottom of the biner. Your right As far as racking goes, to each their own.
|
|
|
|
|
csproul
Oct 12, 2012, 2:58 PM
Post #10 of 19
(14196 views)
Shortcut
Registered: Jun 4, 2004
Posts: 1769
|
corno32 wrote: patto wrote: No possibility of runaway nuts. I carry 30 nuts while climbing racked across 3 oval notchless biners. Most of the rest of my rack are notched biners of phantoms and neutrinos. I'd slightly prefer light notchless but heliums are not cheap! notchless ovals sound very nice, are you talking about something like the aluminum smc ? [image]http://www.columbussupply.com/images/products/rope/carabiner-nlaoc.jpg[/image] I can't find any other notchless ovals thanks Hard to tell from the small picture, but those do not look like notchless to me.
|
|
|
|
|
patto
Oct 12, 2012, 4:29 PM
Post #11 of 19
(14162 views)
Shortcut
Registered: Nov 15, 2005
Posts: 1453
|
rocknice2 wrote: Your acting like accidents never happen. Should is the key word in your statement. ..... It can save a nut if you don't have all your non-placed nuts at the bottom of the biner. I think you are misinterpreting the word should. Equally if you are belaying you should keep control of the brake side. Failure to do so can result in death. I don't see how ensuring that all the nuts are at the bottom of the biner before opening it is a task where failure can be expected. I've placed thousands of nuts and haven't had a run away nut yet.
corno32 wrote: notchless ovals sound very nice, are you talking about something like the aluminum smc ? I can't find any other notchless ovals thanks I use KONG notchless, the old style ones made from round bar stock. DMM also make a nice oval called the Ultra O.
(This post was edited by patto on Oct 12, 2012, 4:34 PM)
|
|
|
|
|
TradEddie
Oct 12, 2012, 5:25 PM
Post #12 of 19
(14143 views)
Shortcut
Registered: Mar 29, 2007
Posts: 164
|
patto wrote: I think you are misinterpreting the word should. Equally if you are belaying you should keep control of the brake side. Failure to do so can result in death. No, should means something is desired or expected, must means something is REQUIRED. So if you are belaying, you must keep control of the brake side. Anyway, I love Ovals for nuts, it drives me crazy if I'm using my partner's rack with his ultralight asymmetrical wiregate crap. I'd probably buy notchless if I needed new ovals, the notch has certainly saved me from dropping nuts, but it won't always do that, and in a tight space, it can cause frustrating snags. TE
|
|
|
|
|
petsfed
Oct 12, 2012, 7:17 PM
Post #13 of 19
(14107 views)
Shortcut
Registered: Sep 25, 2002
Posts: 8599
|
patto wrote: I think you are misinterpreting the word should. Equally if you are belaying you should keep control of the brake side. Failure to do so can result in death. I don't see how ensuring that all the nuts are at the bottom of the biner before opening it is a task where failure can be expected. I've placed thousands of nuts and haven't had a run away nut yet. I do it because I've had issues with carabiners getting unclipped while climbing offwidths, and I climb offwidths often enough that it was something worth getting concerned about. By and large, I don't notice the difference, and I actually switched back to notched carabiners (wiregates) for my cams because it just never came up.
|
|
|
|
|
acorneau
Oct 12, 2012, 7:35 PM
Post #14 of 19
(14097 views)
Shortcut
Registered: Feb 6, 2008
Posts: 2889
|
corno32 wrote: notchless ovals sound very nice, are you talking about something like the aluminum smc ? [image]http://www.columbussupply.com/images/products/rope/carabiner-nlaoc.jpg[/image] I can't find any other notchless ovals thanks Those are notched-nose biners. This is an example of a keygate/notchless biner... Petzl has their "OK" but only in locker form... I'm sure there are more but those a the first two that came to mind.
|
|
|
|
|
Khoi
Oct 12, 2012, 10:00 PM
Post #15 of 19
(14048 views)
Shortcut
Registered: Apr 11, 2008
Posts: 294
|
patto wrote: rocknice2 wrote: I hate notched biners. The whole rack is notchless, with the exception of the 2 stopper racking biners. That little notch comes in handy for capturing runaway nuts. As far as racking goes, each to their own really. But that said.... If you are getting run away nuts then you are doing it wrong! ( IMO) At no stage should the biner be open except when the desired nut is placed and all the nuts are in the bottom basket. When this occurs the gate can be opened and the emplaced nut slipped off aided by no notch. No possibility of runaway nuts. I carry 30 nuts while climbing racked across 3 oval notchless biners. Most of the rest of my rack are notched biners of phantoms and neutrinos. I'd slightly prefer light notchless but heliums are not cheap! Best price on the planet! http://www.mec.ca/...clean-wire-biner.jsp
acorneau wrote: corno32 wrote: notchless ovals sound very nice, are you talking about something like the aluminum smc ? [image]http://www.columbussupply.com/images/products/rope/carabiner-nlaoc.jpg[/image] I can't find any other notchless ovals thanks Those are notched-nose biners. This is an example of a keygate/notchless biner... [image]http://www.madrockclimbing.com/lib/resize.aspx?src=/img/up/OvalTech_020210.jpg&width=400[/image] Petzl has their "OK" but only in locker form... [image]http://www.petzl.com/files/imagecache/product_outdoor_slideshow_image/node_media/ok-2_9.jpg[/image] I'm sure there are more but those a the first two that came to mind. Petzl has their "Owall". http://www.petzl.com/...g-carabiners-0/owall
|
|
|
|
|
acorneau
Oct 13, 2012, 12:55 PM
Post #16 of 19
(13997 views)
Shortcut
Registered: Feb 6, 2008
Posts: 2889
|
Bingo. I thought they had a non-locker oval but I missed it on the webpage.
|
|
|
|
|
louBlissab
Oct 13, 2012, 1:44 PM
Post #17 of 19
(13990 views)
Shortcut
Registered: Apr 9, 2009
Posts: 53
|
Petzl Spirits...just be careful not to drop all your stoppers when the gate opens.
|
|
|
|
|
guangzhou
Oct 19, 2012, 4:05 AM
Post #18 of 19
(13779 views)
Shortcut
Registered: Sep 27, 2004
Posts: 3389
|
Yet another super important RC.com I never give much thought to.
|
|
|
|
|
dcfdrescue2
Oct 19, 2012, 6:29 PM
Post #19 of 19
(13713 views)
Shortcut
Registered: Oct 28, 2009
Posts: 13
|
corno32 wrote: patto wrote: No possibility of runaway nuts. I carry 30 nuts while climbing racked across 3 oval notchless biners. Most of the rest of my rack are notched biners of phantoms and neutrinos. I'd slightly prefer light notchless but heliums are not cheap! notchless ovals sound very nice, are you talking about something like the aluminum smc ? [image]http://www.columbussupply.com/images/products/rope/carabiner-nlaoc.jpg[/image] I can't find any other notchless ovals thanks Rock Exotica makes some nice key gate oval biners http://rockexotica.com/...arabiners/rocko.html
|
|
|
|
|
|