|
mrdtm
Apr 20, 2004, 2:07 AM
Post #1 of 12
(2710 views)
Shortcut
Registered: Apr 10, 2004
Posts: 23
|
After a recent day of slacklining i cannot get one of my 8s on a bite out of my webbing.... does anyone have any spiffy little tricks that help? and... would there b a damaging problem in just leaving it in there? thnx for the tips!
|
|
|
|
|
scclimber
Apr 20, 2004, 2:30 AM
Post #2 of 12
(2710 views)
Shortcut
Registered: Jun 9, 2003
Posts: 159
|
i just use a key to get knots in webbing loose.
|
|
|
|
|
moeman
Apr 20, 2004, 3:14 AM
Post #3 of 12
(2710 views)
Shortcut
Registered: Nov 1, 2002
Posts: 1417
|
Try soaking it in water to loosen up the webbing a bit. thewater won't hurt it- just let it dry before using the webbing again. Next time try using a clove hitch instead of an 8. It will be much easier to untie.
|
|
|
|
|
mrdtm
Apr 20, 2004, 3:17 AM
Post #4 of 12
(2710 views)
Shortcut
Registered: Apr 10, 2004
Posts: 23
|
Thanks both of you... i wil have to try that in a sec. thanks alot for the advice!
|
|
|
|
|
stuck
Apr 20, 2004, 3:42 AM
Post #5 of 12
(2710 views)
Shortcut
Registered: Jun 1, 2003
Posts: 76
|
hit it with a hammer. and get used to have a designated slackline with a welded knot at the end.
|
|
|
|
|
coldclimb
Apr 20, 2004, 4:52 AM
Post #6 of 12
(2710 views)
Shortcut
Registered: Jan 14, 2002
Posts: 6909
|
I use pliers, carefully. Works without problems so far, but it still kinda makes me wonder. :?
|
|
|
|
|
wallwombat
Apr 20, 2004, 5:11 AM
Post #7 of 12
(2710 views)
Shortcut
Registered: Jun 17, 2003
Posts: 727
|
In reply to: hit it with a hammer. Thats the biz.
|
|
|
|
|
apollodorus
Apr 20, 2004, 7:41 AM
Post #8 of 12
(2710 views)
Shortcut
Registered: Feb 18, 2002
Posts: 2157
|
Use the hammer. Tap the knot while turning it around and around. Don't smash the webbing, just tap and loosen it. If you are on a climb with no hammer and need to get a knot loose, you can swing it against the rock.
|
|
|
|
|
areyoumydude
Apr 20, 2004, 7:48 PM
Post #9 of 12
(2710 views)
Shortcut
Registered: Dec 28, 2003
Posts: 1971
|
slackline joe wrote "use two biners in the actual clove hitch - so when you're done you can actually pry the knot apart with the 2nd biner fairly easily. Works very well."
|
|
|
|
|
gds
Apr 20, 2004, 8:39 PM
Post #10 of 12
(2710 views)
Shortcut
Registered: Mar 8, 2004
Posts: 710
|
Sailors use a very rounded, smooth spike. (Often foiund as an extra on a sailing pocket knife) You (carefully) work in the point and then can pry the knot loose. I know it sounds scary but with care there will no damage.
|
|
|
|
|
keinangst
Apr 20, 2004, 8:43 PM
Post #11 of 12
(2710 views)
Shortcut
Registered: Apr 1, 2003
Posts: 1408
|
Seriously, folks, all too complicated... Place it on a rock. GENTLY put your heel onto it and rock over it smoothly, back and forth. The knot will come right out. If you are rough, you can fray the webbing over time. However, I've done this numerous times with zero damage. Works like a charm.
|
|
|
|
|
nicebooty
Apr 21, 2004, 3:44 AM
Post #12 of 12
(2710 views)
Shortcut
Registered: Feb 19, 2004
Posts: 100
|
tie a clove hitch on the one biner, and when ur done turn it the oppoiste direction and wiggle it and it comes loose
|
|
|
|
|
|